read RemovALL 210 product label


The Eco-Powerful™ remover

This powerful paint stripping formula is engineered to remove most paints including polyureas, urethane, epoxy, lacquer, vanish, alkyd and latex paints from steel, aluminum, wood, masonry, brick and concrete.

Features & Benefits

Non hazardous • Non-toxic • Non-Flammable • Low odor • Biodegradable • Water based • Easy clean up • Reduces labor • Reduces pollution

SARA Technology

SARA Technology utilizes physical energy released by chemical reactions to break the bond between the coating and the substrate, lifting the paint right off the surface. The paint chips can be easily removed by vacuum suction, scraping or pressure washing.

 

click here to purchase RemovALL products


RemovALL™
Tough on Paint – Easy on the Environment™
Industrial Paint remover
RemovALL 210
For Metal & Concrete
Spray Grade

Preparation:
Cover / protect areas where the paint is to be left on. Remove masking tape immediately after application as the remover may soak through the tape, damaging the paint beneath it. Thoroughly mix the remover, prior to use, with a high speed drill mixer if available.

Test Patch:
Always prepare a test patch in an inconspicuous area prior to full application. This will indicate the time required and suitability of product.

Application:
Apply a thick, even layer onto the coating being removed. An airless spray machine is the most effective means for application. Use a tip size of 700 microns (.019in) or larger. Brushing and rolling produce lower film builds, requiring additional applications resulting in longer strip times. Once applied, leave the product alone, as agitation slows down penetration.

Coverage:
The desirable thickness of remover is approximately one and a half times the dry film thickness of the paint. Minimum thickness should be 15 mils (wet film). Yield is approximately 40 to 75 sq. ft. per gallon.

Re-Application:
If poor adhesion exists between paint layers, the remover may lift the coating layer by layer. If this happens, remove the lifted layers and re-apply remover. While the removal process is taking place do not allow the remover to dry on the surface. If it starts to dry, reapply the remover.

Dwell Time:
The time required for penetration varies according to the types of paint, the number of layers to be removed and the temperature. Most paint systems will take between 1 and 6 hours. Leaving the remover overnight will provide best results.

Removal:
Removal of residue can be completed by scraper, squeegee, wet/dry vacuum system or by high pressure (2,500 – 3,500 psi) water wash. Dispose of solid paint waste in accordance with government regulations.

Temperature:
Above 55°F (13°C). If working in cooler temperatures expect a longer dwell time. Keep from freezing.

Limited Guarantee / Warranty:
The manufacturers’ liability under any express or implied guarantee/warranty is limited solely to replacement of products shown defective or a refund of the purchase price. Claims must be made within one year of purchase and be accompanied by proof of purchase. The manufacturer shall not be liable for injury, cost of labor, or direct, incidental or consequential damages.


RemovALL Product Selection Guide
  Wood Concrete Brick Metal Plastic
Latex 310 210 310 210 910
Alkyd 310 210 310 210 910
Thick films of above 910 910 910 910 910
Zinc Based Coatings  
Inorganic zinc   510 / 210 510 / 210 510 / 210 510 / 210
Organic zinc   510 / 210 510 / 210 510 / 210 510 / 210
Polyureas - Epoxies  
100% solids 110 510 510 510 510
Solvented epoxies 110 210 210 210 210
Water based epoxies 110 510 510 510 510
Urethanes  
Thin film urethanes 210 210 310 210 510
Rigid & elastrometric urethanes 310 510 / 210 310 310 510
Graffiti  
Painted, non-porous surface 400 400 400 400 400
Unpainted, porous surface 310 310 310 310 310
Penetrating stains, sealers 910 310 310 510 / 210  
Adhesives & carpet underlay 700 700 700 700 700
Dip tanks for stripping small parts       200 200
Paint gun & equipment cleaning

use RemovALL 300

In many cases, the coating type may be unknown.  This chart is only a guideline.  Always do a test patch to determine which RemovALL product is best suited for any particular job.  This will also indicate the dwell time required to complete the project and suitability for the substrate.
 

Avoid contact with eyes and skin. Prolonged and repeated exposure to skin may cause irritation.  Wash hands after using. Keep container closed when not in use. Do no transfer contents to other containers for storage.

CONTAINS:
ALCOHOLS. Use only with adequate ventilation. To avoid over exposure, open window and doors or use other means to ensure fresh air entry during application and dwell time. If you experience eye watering, headaches or dizziness, increase fresh air or wear respiratory protection (NIOSH approved) or leave the area. Rubber gloves and safety glasses are recommended.

FIRST AID:
In case of eye contact, flush thoroughly with large amounts of water for 15 minutes. If irritation persists, get medical attention. For skin contact, wash thoroughly with soap and water. In case of respiratory difficulty, provide fresh air and call physician. If swallowed, get medical attention immediately.


DO NOT TAKE INTERNALLY
KEEP OUT OF REACH OF CHILDREN
FOR PROFESSIONAL USE ONLY


INGREDIENT   C.A.S.#
ARYL ALCOHOL (100-51-6)
PROPYLENE GLYCOL (57-55-6)
DISTILLATES (PETROLEUM) (68477-31-6)

Made in Canada

click here to purchase RemovALL products



page bottom
homeprivacy

DTEP Archival Record
 109 S Wayne Ave  •  Lockland OH  •  45215

Product names contained on this site are for identification purposes only.
All trademarks and registered marks are the property of their respective owners.


 Visit our StoreFront

Copyright © 2002 - 2016 Small's Hardware Inc.  All rights reserved.