Ultra-Strip
maximum strength paint remover
is a safer, environmentally friendlier paint remover
formulated for maximum stripping action.
|
| |
Ultra-Strip, the ultimate
safe paint remover is utilized for maximum paint stripping action.
Ultra-Strip paste is environmentally friendly, biodegradable, non-flammable,
water rinse-able and contains no methylene chloride, caustic or
other harsh chemicals. For those applications where time of application
and removal is critical, a lighter coat lifts 1 to 4 layers of paint
usually in 15 minutes to four hours. Where multiple layers
of paint are indicated, or there are other more difficult coatings
such as two part epoxies and urethanes a heavier coat will remove
the paint in one application. Ultra-Strip maximum strength paint
remover works on a multitude of surfaces including wood, metal,
plaster, masonry, fiberglass, etc. As a non-caustic remover, the
surface does not need to be neutralized. For application,
Ultra-Strip maximum strength paint remover can be brushed, rolled
or sprayed.
|
|
|
|
Preparation |
 |
Mask any areas not
being stripped with plastic and masking tape.
|
|
|
If product freezes
in bucket, let thaw and stir vigorously until product
is consistent.
|
|
|
Hints |
|
If Ultra-Strip maximum
strength paint remover is applied too thinly, left on too
long, or due to excessive heat conditions, the applied area
is difficult to scrape, try the following:
|
|
|
Mist the applied area
with After Strip, wait 5-15 minutes and remove.
|
|
|
Reapply Ready-Strip
over itself, wait 15 to 30 minutes and remove.
|
|
|
If neither choice
above works, scrape off product and reapply.
|
|
|
|
 Ready
Strip Wash paint remover clean-up is the manufacturers recommended
product for removing residue and softened layers that often
remain after the paint stripping or varnish removal process.
It cleans and prepares the surface for refinishing.
This environmentally safe solution contains no methylene
chloride or harsh chemicals, is non-flammable, non-combustible
and biodegradable.
|
|
Since it is
often hard to know the type or the amount of paint on a
surface, small test areas should be stripped to determine
the proper application and dwell time needed for paint removal
to occur.
(read instructions)
|
|
|
| |
|
|
| |
For stripping 1 to 4 layers of
paint quickly - Apply Ultra-Strip maximum strength paint remover
to the surface at a total of approximately 1/64" thick (10 to 15
mils) with a brush, roller, trowel, putty knife or sprayer. Can
be sprayed effectively using an airless sprayer.
Drill mix before spraying - Remove filters
from sprayer & spray gun. Submerge pump directly into remover.
Do not use suction hose. Use NEW 1/4" or 3/8" airless hose.
Use at least a 1 GPM piston sprayer, .019 - .021 reversible spray
tip. A wet mil gauge should be used to measure thickness.
Let the product dwell from 15 minutes to 4 hours. Follow Suggested
Removal Techniques below. Coverage will vary between 100 and 150
sq. ft. per gallon when this application method is used. For
removal of multiple layers or stubborn coatings -
consult test patch guidelines. Ultra-Strip
maximum strength paint remover will easily cling to vertical surfaces.
Use your tool to fill detailed, intricate or grooved surfaces. For
best results apply at temperatures between 60° F and 80° F. Product
activity is reduced below a temperature of 60° F and may require
additional dwell time before all layers of paint are removed. If
product freezes let thaw and stir vigorously until product is consistent.
No Neutralization required. Clean tools promptly after use with
soap and water.
|
|
 |
Friendlier for you
● Friendlier for your Environment |
|
| |
|
Suggested Removal Techniques
|
|
| |
|
|
| |
Easiest removal is achieved using
a 4in or wider razor blade scraper (commonly known as a wallpaper
remover) to lift the remover/paint off the surface.
|
Easiest removal is achieved using
a Back To Nature Stainless Steel Scraper to strip remover/paint
from the surface. Use a stiff bristle brush with Ready Strip Wash
paint remover clean-up paint remover wash to remove any residue.
|
| |
| Decorative
Plaster or Wood |
|
|
| |
Use a Back To Nature Stainless
Steel Scraper with 5 function detail blade to lift the remover/paint
off the surface. Use a stiff bristle brush with Ready Strip Wash
paint remover clean-up to remove any residue.
|
Use a putty knife to lift the
remover/paint from the surface. Use a stiff bristle brush with Ready
Strip Wash paint remover clean-up to remove any residue remaining.
|
| |
| Masonry,
Concrete Surfaces |
|
|
| |
Remove bulk of remover/paint with
a stiff putty knife or wire brush. Use a wire brush with Ready Strip
Wash paint remover clean-up to remove any residue remaining.
Residue can also be removed with a high pressure washer where permitted.
|
Agitate or rough up remover/paint
on the surface with a wire brush without attempting removal. This
helps to lift bottom layers from the surface. Use a 4in or wider
razor blade scraper (wallpaper remover) or stiff putty knife (pipe
railings or irregular surfaces should use the putty knife) to lift
remover/paint off the surface. Use a wire brush with Ready Strip
Wash paint remover clean-up to remove any residue remaining.
|
| |
|
|
| |
Misting the applied area with
Ready Strip Wash paint remover clean-up prior to removal makes lifting
of the paint or varnish easier. Misting with Ready Strip Wash paint
remover clean-up also reactivates the product if it feels dry to
the touch. Any paint residue left on a surface should be removed
within a short period of time so that paint residue will not dry
up re-adhere. In some circumstances, it may look like the last layer
of paint is still on the surface. This is not a dried layer
of paint, but paint & remover which has been emulsified so that
it can be removed.
|
Safety goggles are recommended
for eye protection. Protective gloves such as butyl rubber, neoprene
gloves are also recommended. Maintain adequate ventilation especially
in confined areas. If spraying or misting is expected use NIOSH
approved chemical cartridge (organic vapor) respiratory equipment
(full face respirator recommended). In case of inhalation remove
victim to fresh air and provide oxygen if breathing is difficult.
In case of eye contact - flush exposed areas with large quantities
of water. In case of skin contact - wash skin with soap and water.
Use emollient skin creams. In case of ingestion - do not induce
vomiting. Call physician immediately.
|
| |
|
to purchase
paint remover or accessories
click
here
|
|
